## automake - create Makefile.in from Makefile.am
## Copyright (C) 1994, 1995, 1996, 1997, 1998 Free Software Foundation, Inc.

## This program is free software; you can redistribute it and/or modify
## it under the terms of the GNU General Public License as published by
## the Free Software Foundation; either version 2, or (at your option)
## any later version.

## This program is distributed in the hope that it will be useful,
## but WITHOUT ANY WARRANTY; without even the implied warranty of
## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
## GNU General Public License for more details.

## You should have received a copy of the GNU General Public License
## along with this program; if not, write to the Free Software
## Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA
## 02111-1307, USA.
# This directory's subdirectories are mostly independent; you can cd
# into them and run `make' without going through this Makefile.
# To change the values of `make' variables: instead of editing Makefiles,
# (1) if the variable is set in `config.status', edit `config.status'
#     (which will cause the Makefiles to be regenerated when you run `make');
# (2) otherwise, pass the desired values on the `make' command line.

@SET_MAKE@

all-recursive install-data-recursive install-exec-recursive \
installdirs-recursive install-recursive uninstall-recursive @INSTALLINFO@ \
check-recursive installcheck-recursive info-recursive dvi-recursive:
	@set fnord $$MAKEFLAGS; amf=$$2; \
	dot_seen=no; \
	target=`echo $@ | sed s/-recursive//`; \
	list='$(SUBDIRS)'; for subdir in $$list; do \
	  echo "Making $$target in $$subdir"; \
	  if test "$$subdir" = "."; then \
	    dot_seen=yes; \
	    local_target="$$target-am"; \
	  else \
	    local_target="$$target"; \
	  fi; \
	  (cd $$subdir && $(MAKE) $(AM_MAKEFLAGS) $$local_target) \
## This trick allows "-k" to keep its natural meaning when running a
## recursive rule.
	   || case "$$amf" in *=*) exit 1;; *k*) fail=yes;; *) exit 1;; esac; \
	done; \
	if test "$$dot_seen" = "no"; then \
	  $(MAKE) $(AM_MAKEFLAGS) "$$target-am" || exit 1; \
	fi; test -z "$$fail"

## We run all `clean' targets in reverse order.  Why?  It's an attempt
## to alleviate a problem that can happen when dependencies are
## enabled.  In this case, the .P file in one directory can depend on
## some automatically generated header in an earlier directory.  Since
## the dependencies are required before any target is examined, make
## bombs.
mostlyclean-recursive clean-recursive distclean-recursive \
maintainer-clean-recursive:
	@set fnord $$MAKEFLAGS; amf=$$2; \
	dot_seen=no; \
	rev=''; list='$(SUBDIRS)'; for subdir in $$list; do \
	  rev="$$subdir $$rev"; \
	  test "$$subdir" != "." || dot_seen=yes; \
	done; \
## If we haven't seen `.', then add it at the beginning.
	test "$$dot_seen" = "no" && rev=". $$rev"; \
	target=`echo $@ | sed s/-recursive//`; \
	for subdir in $$rev; do \
	  echo "Making $$target in $$subdir"; \
	  if test "$$subdir" = "."; then \
	    local_target="$$target-am"; \
	  else \
	    local_target="$$target"; \
	  fi; \
	  (cd $$subdir && $(MAKE) $(AM_MAKEFLAGS) $$local_target) \
## This trick allows "-k" to keep its natural meaning when running a
## recursive rule.
	   || case "$$amf" in *=*) exit 1;; *k*) fail=yes;; *) exit 1;; esac; \
	done && test -z "$$fail"